武汉莫诺转子免费咨询「螺耐斯」[螺耐斯10e361c]内容： 管柱脱落是自由式管柱结构经常发生的一种现象，这是由于正常运转时转子旋转对定子产生的摩擦扭矩方向实际上是定子及油管的连接螺纹的卸扣方向，如果摩擦力矩大于油管扣的上扣扭矩，油管就脱扣。当尾管很重时，还会出现螺纹掳扣。当管柱脱落时，通过作业重新连接好就能恢复生产。如果未发生螺纹掳扣，可以采取对扣方式打捞，如果发生掳扣，必须下打捞工具进行打捞。Column shedding is a common phenomenon of free tube structure, which is due to the direction of rotation of the friction torque generated by the stator rotor during normal operation is actually a stator and tubing connection1 screw shackle direction, if the friction torque is greater than the pipe le on torque, oil pipe tripping. When the tail pipe is very heavy, there will also be a thread caption. When the pipe column falls off, the production can be restored by reconnecting the work. If the le is not threaded, it can be salvaged by the way of the le. If the le occurs, the fishing tool must be salvaged.
Ａ、定子A, stator定子是螺杆泵的一个关键部件，并直接影响到井下机组的寿命。定子制造质量越高，井下机组的寿命就越长。定子的作用就是提供转子工作和液体抽汲的螺旋腔，其结构非常简单，由钢制外壳和塑料／橡胶衬套内腔有双螺旋、三螺旋、四螺旋甚至五螺旋、六螺旋，在相同尺寸下，螺旋数越多，泵的排量越高。The stator is a key component of the screw pump, which directly affects the life of the downhole unit. The higher the quality of the stator, the longer the life of the downhole unit. The role is to provide a rotor stator and liquid pumping spiral cavity drain, the structure is very simple, a steel shell and a plastic / rubber bushing cavity with double helix, three helix, four or even five, six spiral helical spiral, in the same size, the number of spiral, the displacement of the pump is high.
Ｅ、抽油杆扶正器E, sucker rod centralizer抽油杆扶正器由心轴和扶正筒组成，它接在两根抽油杆之间，被卡在两个抽油杆接箍之间。心轴也就是一要极短的抽油杆短节。扶正筒是一个内孔比心轴大１ＭＭ左右的空心塑料筒，外部有四个略比油管内径小的扶正翼，采取浇注成型。扶正筒可以围绕心轴转动，防止抽油杆旋转时与内壁接触而磨蚀油管，又可以让流体通过。The sucker rod centralizer is comed of the heart shaft and the upright cylinder, which is connected between the two sucker rods and is stuck between the two sucker rod hoops. The axis of the heart is also an extremely short rod short section. The centering cylinder is a hollow plastic tube inner hole Bixin shaft around 1MM, external four slightly smaller than the diameter of the tubing centralizer wing, adopt casting. The centralizer can revolve around the axis to prevent the sucker rod from touching the inner wall when it rotates, and it can also let the fluid pass through.
Ｆ、抽油杆F, sucker rod所使用的抽油杆是常用的普通抽油杆、空心抽油杆和连续抽油杆，可根据油井确定。The sucker rod used is commonly used as a common 1sucker rod, hollow sucker rod and continuous sucker rod, which can be determined according to the oil well.Ｇ、定子扶正器G, stator centralizer定子扶正器为有一定弹性的笼形装罩，每一对由两半构成，中间大、两端小。作用是使定子居中和减小定子的摆动。The stator centralizer is a cage shaped cover with a certain elasticity. Each pair is made up of two halves, large in the middle and small at both ends. The function is to make the stator middle and reduce the stator wobble.Ｈ、锚定装置H, anchoring device对于没有封隔器的井和泵挂深度浅的井，用于固定定子、消除摆动和防止定子脱扣。采用普通的锚定装置即可。For wells without packers and shallow wells with deep pumps, it is used to fix the stator, eliminate the swinging and prevent the tripping of the stator. A common anchoring device can be used.
以上信息由专业从事莫诺转子的螺耐斯于2024/5/20 10:50:28发布
转载请注明来源：http://m.tz1288.com/qynews/lnshbsb-2755875903.html
上一条：沙坡头区桶装水配送电话服务周到 宁夏贺兰雪纯净水公司
下一条：不锈钢拼装水箱询价咨询「苏州鸿迪金属制品」
