Ｅ、抽油杆扶正器E， sucker rod centralizer抽油杆扶正器由心轴和扶正筒组成，它接在两根抽油杆之间，被卡在两个抽油杆接箍之间。心轴也就是一要极短的抽油杆短节。扶正筒是一个内孔比心轴大１ＭＭ左右的空心塑料筒，外部有四个略比油管内径小的扶正翼，采取浇注成型。扶正筒可以围绕心轴转动，防止抽油杆旋转时与内壁接触而磨蚀油管，又可以让流体通过。The sucker rod centralizer is comed of the heart shaft and the upright cylinder， which is connected between the two sucker rods and is stuck between the two sucker rod hoops. The axis of the heart is also an extremely short rod short section. The centering cylinder is a hollow plastic tube inner hole Bixin shaft around 1MM， external four slightly smaller than the diameter of the tubing centralizer wing， adopt casting. The centralizer can revolve around the axis to prevent the sucker rod from touching the inner wall when it rotates，莫诺定子， and it can also let the fluid pass through.



Ｄ、限位器D， limiting device限位器为一个底部带限位板和流通通道的短节，接在定子的尾部，其作用是施工作业时给转子限位以防止下入过头而失去作用和杆柱脱落时防止杆柱掉入井底。The limiting device is a short section with bottom limit plate and distribution channel， which is connected to the tail of the stator. Its function is to limit the rotor to the rotor during ctruction1， so as to prevent it from falling into the overhead and lose its function and prevent the rod from falling into the bottom when the rod string falls off.



Ｆ、抽油杆F， sucker rod所使用的抽油杆是常用的普通抽油杆、空心抽油杆和连续抽油杆，可根据油井确定。The sucker rod used is commonly used as a common 1sucker rod， hollow sucker rod and continuous sucker rod， which can be determined according to the oil well.Ｇ、定子扶正器G， stator centralizer定子扶正器为有一定弹性的笼形装罩，每一对由两半构成，中间大、两端小。作用是使定子居中和减小定子的摆动。The stator centralizer is a cage shaped cover with a certain elasticity. Each pair is made up of two halves， large in the middle and small at both ends. The function is to make the stator middle and reduce the stator wobble.Ｈ、锚定装置H， anchoring device对于没有封隔器的井和泵挂深度浅的井，用于固定定子、消除摆动和防止定子脱扣。采用普通的锚定装置即可。For wells without packers and shallow wells with deep pumps， it is used to fix the stator， eliminate the swinging and prevent the tripping of the stator. A common anchoring device can be used.



莫诺定子-螺耐斯(推荐商家)由武汉螺耐斯环保设备有限公司提供。武汉螺耐斯环保设备有限公司是一家从事“螺杆泵,单螺杆泵,螺杆阀,污泥切割机,污泥破碎机,微型螺杆泵”的公司。自成立以来，我们坚持以“诚信为本，稳健经营”的方针，勇于参与市场的良性竞争，使“螺耐斯”品牌拥有良好口碑。我们坚持“服务至上，用户至上”的原则，使螺耐斯在污水处理设备中赢得了客户的信任，树立了良好的企业形象。 特别说明：本信息的图片和资料仅供参考，欢迎联系我们索取准确的资料，谢谢！